中文
+ 更多 联系我们
联系我们

苏州威旻达机械设备有限公司

联系人:王经理

手机:15906136866

电话:0512-68136800

传真:0512-68136800

地址:苏州市吴中区吴中大道5399号 

公司新闻

铝合金门窗玻璃铝条切割的加工装置

2018-06-25 点击数:441
铝合金门窗加工设备合片机用垂直定位机构托板固定在托板支板上,在托板支板的下面有两个升降缸,升降缸是由升降缸导轴外套升降缸导套构成,托板支板就固定在两升降缸导套上,在两升降缸导套的外壁各铰接有杠杆,杠杆的支点铰接有支板,杠杆的另一端与联动杆铰接,联动杆再与油缸的油缸轴铰接;另外,在托板的一侧还有一个托板定位器。
The vertical positioning mechanism bracket of the aluminum alloy door and window processing equipment is fixed on the plate support plate. There are two lifting cylinders under the support plate. The lifting cylinder is composed of the lifting cylinder guide sleeve of the guide shaft of the lifting cylinder. The bracket plate is fixed on the guide sleeve of the two lifting cylinder, and the outer wall of the two elevator guide sleeve is articulated with levers and bars. The support point of the rod is articulated with a supporting plate, the other end of the lever is articulated with the linkage rod, and the linkage rod is rehinged with the oil cylinder shaft of the oil cylinder. In addition, there is a plate positioner on the side of the bracket.

门窗倾斜问题:门窗在安装完毕后,出现了倾斜、门扇走扇推拉不好的现象,这主要是由于安装人员在安装过程中没有用线坠,靠尺检查门窗与地面或台面的垂直度,造成偏差过大。铝合金门窗加工设备因此安装门窗时,一定要按安装规范去做。门窗不水平:门窗安装后,出现一头高一头低、扇和框的缝隙不均匀现象,有时存在上宽下窄或下宽上窄的问题。

移门生产设备

Door and window slant problem: after the installation of the door and window, there is a bad phenomenon of slanting and door fan, which is mainly due to the failure of the installation staff in the installation process, and the verticality of the doors and windows and the surface or the table is checked by the ruler, resulting in too much deviation. Aluminum alloy doors and windows processing equipment, so when installing windows and doors, we must follow the installation specifications. The doors and windows are not horizontal: after the doors and windows are installed, there is an uneven gap between the top and the bottom, the fan and the frame, and sometimes there is a problem of wide width, narrow width or narrow width.
处理这种问题,首先要测量窗台或地面的水平度,看一下哪边高,然后以高点为基准,低的地方用木楔或垫块临时固定,以调整窗框的水平度。水平度调好了,窗子就不会出现一边高一边低的现象。托板定位器是在步进电机的出轴上固定一垂直的丝杠,在丝杠上通过螺纹连接一个光电传感器。
To deal with this problem, we should first measure the level of the windowsill or the ground, see which side is high, and then take the high point as the base, and the low places are temporarily fixed with the wedges or padding blocks to adjust the level of the window frame. When the level is adjusted, the window will not appear high and low. The supporting plate positioner is fixed with a vertical screw on the outlet shaft of the stepping motor, and a photoelectric sensor is connected to the screw rod through threads.
丝杠采用滚珠丝杠。玻璃铝条切割装置由摆臂、A销轴、夹紧块、固定块、锯片、电机、连接板、A气缸、底板、支架、接头、气缸板、B气缸、气缸尾座、B销轴、垫片和电机接头组成。软头快速连接的装置,包括灯罩、与带电线的端子注塑为一体的软头,还包括紧套在灯罩尾端外的塑胶卡套,铝合金门窗加工设备塑胶卡套的外表面上至少有一个凸起点,软头的内表面上有宽度与凸起点相适配的轴向导向槽及与轴向导向槽垂直并相通的止推槽。前出装置包括平台、传送辊和支撑轮,平台的两端分别铰接有转板,两转板之间连接有横梁,传送辊设置于横梁上;平台与转板之间设有一组活塞杆、气缸作为转板的驱动机构,活塞杆铰接于平台上,气缸铰接于转板上。敲打门框要用塑锤轻轻地敲,切不可用铁锤去敲。
The ball screw is best used for the screw. The glass aluminum strip cutting device consists of swinging arm, A pin shaft, clamping block, fixed block, saw blade, motor, connecting plate, A cylinder, floor, bracket, joint, cylinder board, B cylinder, cylinder tail seat, B pin shaft, gasket and motor joint. A device for fast connection with a soft head, including a light cover, a soft head that is injected into the terminal of a live line, and a plastic jacket that is tightened outside the end of the lamp cover. At least one convex starting point is on the outer surface of the plastic card sleeve of the aluminum alloy door and window processing equipment, and the inner surface of the soft head has an axial direction slot suitable for matching the convex starting point. A thrust slot that is perpendicular to the axial direction groove and interconnected. The fore out device includes the platform, the transmission roll and the supporting wheel. The two ends of the platform are articulated with a rotating plate respectively. The cross beam is connected between the two rotating plates. The transfer roller is set on the beam. A group of piston rods and cylinders are set between the platform and the rotating plate as the driving mechanism of the rotating plate. The piston rod is articulated on the Yu Ping platform, and the cylinder is articulated to the rotating plate. Knock the doorframe with a plastic hammer and knock it lightly.
感谢您的阅读,此文的文章来源:移门生产设备更多的内容和问题请点击:http://www.szwmdjx.com 我们会继续努力的为您提供服务,感谢您的支持!
Thank you for your reading, the source of this article: the more content and problems of the transfer door production equipment, please click: we will continue to work hard for you to provide service, thank you for your support!
友情链接:全民彩票官网  58彩票官网  苹果彩票官网  58彩票  菠萝彩票  东方彩票  皇冠彩票  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!